ABB RVC (148 pages)
Tags
Languages available:
No exact matches found. Please change your query
Need help?
Do you have a question about the product that is not answered in the manual?
- Receive updates on solutions
- Get answers to your question
Product description:
Frequently Asked Questions
What should I do before using the RVC controller?
Before using the RVC controller, ensure that you have both parts of the manual (2GCS201086A0050 1/2 & 2/2) available for reference during installation, maintenance, and operation.
How do I install the RVC controller?
To install the RVC controller, slide it into the capacitor bank cubicle, insert the mounting brackets into the corresponding fixation holes, and tighten the screws until the controller is securely fixed.
What are the wiring connections for the RVC controller?
The RVC controller requires connections for the current transformer (k, I), voltage inputs (L2, L3), and alarm contacts (M1, M2). The output relay common source (A) and outputs (1-12) should also be connected according to the wiring diagram.
How does the RVC controller switch capacitor steps?
The RVC controller calculates the reactive power requirement based on the average load during a switching delay time (minimum 40 seconds). It switches on the largest step first to avoid intermediate switching and introduces a 12-second delay between steps to prevent transient issues and meet EMC requirements.
What are the different modes of operation for the RVC controller?
The RVC controller has several modes: AUTO mode (default), where the controller automatically adjusts steps to reach the target power factor; MAN mode, where the user manually controls the steps; and AUTO SET mode, which allows the user to set the target power factor and other parameters.
question
The C/k parameter represents the sensitivity of the controller, set to about two-thirds of the current of the smallest switched step. It is related to the power of the smallest step (Q in kvar), nominal voltage (V), and CT ratio (k). The acceptable range is 0.01 ≤ C/k ≤ 3.00.
How does the RVC controller handle overvoltage and undervoltage conditions?
The RVC controller has protection settings for overvoltage (Max Vrms) and undervoltage (Min Vrms). If the system voltage exceeds the Vmax limit or falls below the Vmin limit, all steps are disconnected. In case of undervoltage, disconnection is faster than one network period.
What should I do if the RVC controller does not switch steps?
If the RVC controller does not switch steps, check that it is in AUTO mode, verify the phase shift and C/k settings, and ensure the CT short-circuit bridge is removed. Also, wait for the delay time between switching or power outage.
How can I troubleshoot if the RVC controller is not working?
If the RVC controller is connected but not working, check the voltage protection settings, fuses, and voltage supply. If the AUTO SET procedure stops and displays an error message, refer to the error message table to identify and resolve the issue.
What happens if the THDV exceeds the set limit?
If the THDV exceeds the user-set over THDV limit, all steps are disconnected. The reset delay time (default 40 seconds) is automatically doubled each time this event occurs. Continuous reduction of THD level can disable the protection, which is indicated by a specific display on the screen.
Related products from ABB
A50
User manual 2 pages
A75
User manual 2 pages
AE75
User manual 2 pages
AE50
User manual 2 pages
TAE50
User manual 2 pages
TAE75
User manual 2 pages
UA50
User manual 2 pages
UA75
User manual 2 pages
A63
User manual 2 pages
AE63
User manual 2 pages
UA63
User manual 2 pages
JSB/S 1.1
User manual 2 pages
MSAH1
User manual 2 pages
MSHD
User manual 2 pages
S3C-MOD230
User manual 2 pages
S3C-MOD24
User manual 2 pages
Safeball JSTD1
User manual 2 pages
SX-ARC1
User manual 2 pages
UA30-30-10RA
User manual 2 pages
UA16-30-10RA
User manual 2 pages