EINHELL 34.034.92 (92 pages)
Tags
Languages available:
No exact matches found. Please change your query
Need help?
Do you have a question about the product that is not answered in the manual?
- Receive updates on solutions
- Get answers to your question
Product description:
Frequently Asked Questions
How to attach the extension pole and blade?
To attach the extension pole, loosen the mounting screw on the motor unit, remove the protective cap from the extension pole, and insert it into the motor unit's mounting slot. Ensure the safety pin clicks into the slot. Secure the extension pole with the mounting screw. To attach the blade, loosen the mounting screw, remove the protective cap from the blade unit, and insert it into the extension pole's mounting slot. Ensure the safety pin clicks into the slot before securing with the mounting screw.
How to adjust the blade angle?
To adjust the blade angle, pull the safety lever backward, grip the adjustment lever, and press the lock lever to set the desired angle. Release the lock lever once the angle is set. Ensure the lock lever clicks into place. Push the safety lever forward to secure the adjustment.
What are the technical specifications of the device?
The device operates on 230-240 V ~ 50 Hz with a power consumption of 900 W. The cutting length is 410 mm, blade length is 480 mm, tooth spacing is 20 mm, and it can cut up to 15 mm thick material. The measured sound pressure level is 90.22 dB(A), and the sound power level is 105 dB(A). Hand-arm vibration measured at the front handle is 2.725 m/s² and at the rear handle is 3.056 m/s². The device weighs approximately 5.3 kg.
How to secure the shoulder strap?
Attach the carabiner of the safety clip into the strap holder as shown in the diagram. Place the shoulder strap over your shoulder and adjust the strap length so the holder is at hip height for comfortable use. The shoulder strap has a safety release mechanism that allows you to quickly detach it in case of an emergency by pulling the release upwards.
What safety precautions should be taken when using the device?
Always wear protective gear such as safety goggles, ear protection, and a helmet. Use gloves and safety boots. Ensure the device is disconnected from the power source before making any adjustments. Keep the device away from water and avoid contact with grounded surfaces. Do not use the device in wet conditions without a residual current device. Maintain a safe distance from overhead power lines.
How to clean and maintain the device?
Clean the device regularly with a damp cloth and a small amount of lubricating soap. Avoid using cleaning solvents as they may damage plastic parts. Keep the device free from dust and debris. Use a brush to remove dirt and apply a light oil film. Ensure no water enters the device's internal components to prevent electrical hazards.
What should be done if the device does not operate?
Check if the power cord is properly connected and verify the circuit breaker. If the device still does not work despite the power supply, send it to the specified service address for further assistance. Ensure the device is not overloaded and that the power source is suitable for the device's requirements.
How to replace the power cord?
If the power cord is damaged, it must be replaced by the manufacturer, their service center, or a qualified electrician to avoid hazards. Never allow the power cord to come into contact with the blade or other moving parts. Ensure the replacement cord is suitable for outdoor use if working in open areas.
What are the recommended cutting techniques for hedges?
Use the dual-sided, counter-rotating blades to cut in both directions for efficient trimming. For even hedge height, use a string line as a guide and trim any overhanging branches. Cut the sides of the hedge with sweeping motions from bottom to top. Avoid touching any objects like wire fences or plant supports to prevent damage to the blade assembly.
How to handle blockages or jams in the blade?
If the blade becomes blocked by a solid object, immediately turn off the device, unplug it, and remove the object. Do not attempt to force the blade to move. Always ensure the device is disconnected from the power source before performing any maintenance or cleaning procedures.
Related products from EINHELL
Bavaria BAS 4,8
User manual 32 pages
REH 680
User manual 52 pages
LE-AS 18
User manual 32 pages
HEC 550
User manual 18 pages
BT-CW 18i
User manual 44 pages
AS-LE 14,4
User manual 28 pages
41.389.00
User manual 32 pages
Bavaria BTBS 710
User manual 32 pages
DSS 260/1
User manual 32 pages
HEC 410
User manual 38 pages
HEC 510
User manual 38 pages
GE-CH 1855 Li Kit
User manual 44 pages
GE-CH 1855 Li Kit
User manual 56 pages
34.109.20
User manual 46 pages
34.109.20
User manual 126 pages
34.109.20
User manual 176 pages
10.508.21
User manual 52 pages
42.599.80
User manual 142 pages
42.599.80
User manual 153 pages
GE-CH 1855/1 Li-Solo
User manual 56 pages