ABB ACS850-04 (108 pages)
Tags
Languages available:
No exact matches found. Please change your query
Need help?
Do you have a question about the product that is not answered in the manual?
- Receive updates on solutions
- Get answers to your question
Product description:
Frequently Asked Questions
How to remove the cover assembly?
To remove the cover assembly, press the tab slightly with a screwdriver, slide the lower cover plate downwards and pull it out, disconnect the panel cable if present, remove the screw at the top, and carefully pull the lower part of the base outwards by the two tabs. Refit the cover in reverse order.
What safety precautions should be taken when working with the drive?
Never work on the drive, braking chopper circuit, motor cable, or motor when input power is applied. Always ensure no voltage is present by measuring. A rotating permanent magnet motor can generate dangerous voltage. Lock the motor shaft mechanically before connecting a permanent magnet motor to the drive or working on a drive system connected to it.
How to install the drive module?
Fasten the drive module to the mounting base using screws through the four mounting holes. Frame A and B can be mounted onto a DIN rail, but it is highly recommended to fasten these modules to the mounting base using two screws through the lower mounting holes.
What are the steps for installing power cables?
Attach the terminal blocks to the drive, remove the plastic connector covers if applicable, fasten the cable clamp plates, strip the power cables so the shields are bare at the clamps, connect the supply, resistor, and motor cables to the appropriate terminals, tighten the cable clamps onto the bare cable shields, connect the ends of the cable shields to the ground terminals using cable lugs, and cover visible bare shield with insulating tape.
What are the wire sizes and tightening torques for power terminals?
For wire sizes, use 0.25 to 4 mm² for -03A0-2…08A0-2 and -03A0-5…08A0-5, 0.5 to 6 mm² for -010A-2…018A-2 and -010A-5…018A-5, and 6 to 70 mm² for -025A-2…094A-2 and -025A-5…094A-5. Tightening torques are 0.5 to 0.6 N·m (4.4 to 5.3 lbf·in) for the first two, and 3 N·m (25 lbf·in) for the last.
How to connect control cables?
Follow the default I/O connection diagram, set the jumpers on the control unit to the appropriate positions, connect the external power input, relay outputs, digital inputs, analog inputs and outputs, and ensure proper grounding. Use the specified wire sizes and tightening torques for each terminal.
What are the tightening torques for terminal headers and jumpers?
For XPOW, XRO1, XRO2, XRO3, and XD24, use 0.5 N·m (5 lbf·in). For XDI, XDIO, XAI, XAO, XD2D, and XSTO, use 0.3 N·m (3 lbf·in). For the clamp plate, use 1.5 N·m (13 lbf·in). For the drive-to-drive link termination jumper, use 0.7 N·m (6.2 lbf·in).
What are the technical specifications for the ACS850-04 drive?
The ACS850-04 is an IP20 drive suitable for use in a heated, indoor controlled environment. It must be installed in clean air, with cooling air free from corrosive materials and electrically conductive dust. The maximum ambient temperature is 40 °C (104 °F) at rated current, and the drive is suitable for circuits capable of delivering up to 100,000 rms symmetrical amperes, 500 V maximum.
What are the requirements for cable ratings in UL-compliant installations?
Cables within the motor circuit must be rated for at least 75 °C (167 °F) in UL-compliant installations. Input cables must be protected with fuses or circuit breakers. Suitable IEC (class gG) and UL (class T) fuses are listed in the Hardware Manual. For circuit breakers, contact your local ABB representative.
What are the requirements for branch circuit protection in the US and Canada?
In the US, branch circuit protection must comply with the National Electrical Code (NEC) and local codes, using UL classified fuses. In Canada, branch circuit protection must comply with the Canadian Electrical Code and provincial codes, also using UL classified fuses. The drive provides overload protection in accordance with the NEC.
Related products from ABB
CP6605
User manual 2 pages
CP6607
User manual 2 pages
CP6621
User manual 2 pages
CP6610
User manual 2 pages
CP6615
User manual 2 pages
ACS355
User manual 4 pages
ACS355
User manual 4 pages
ACS355
User manual 82 pages
ACS320
User manual 4 pages
ACS320
User manual 4 pages
ACS310
User manual 4 pages
ACS310
User manual 4 pages
ACS350
User manual 4 pages
ACS350
User manual 4 pages
ACS850 series
User manual 82 pages
ACS850 series
User manual 196 pages