Protool CSP 56-2 EB (136 pages)
Languages available:
No exact matches found. Please change your query
Need help?
Do you have a question about the product that is not answered in the manual?
- Receive updates on solutions
- Get answers to your question
Product description:
Frequently Asked Questions
How to adjust the cutting depth?
To adjust the cutting depth, loosen the tension lever [3-1], set the cutting depth using the scale [3-2] to the desired measurement, and then tighten the tension lever again. The cutting depth is correctly set when the saw blade protrudes no more than 3 mm from the workpiece.
How to set the cutting angle?
To set the cutting angle, loosen the wing screw [4-2], adjust the angle using the scale [4-3] to the desired value, and then tighten the wing screw again. Note that the maximum cutting depth is limited during diagonal cuts.
How to use the guide for marking the cut line?
The edge [4-1] aligns with the center of the saw blade for right-angle cuts (90°) and for diagonal cuts. When using the guide rail (GRP 800/1400/3000-2), the edge of the cut indicator matches the center of the saw blade for all cutting angles between 0° and 45°. Without the guide rail, the edge follows the center of the saw blade only during perpendicular cuts.
How to install the parallel guide?
Insert the parallel guide [1-9] into the holders in the base plate [1-7] and secure it with wing screws [1-12]. The parallel guide allows for parallel cuts along a straight edge and cutting strips of equal width. The maximum adjustable cut width is approximately 100 mm.
How to change the saw blade?
Before changing the saw blade, unplug the device from the power outlet. Wear protective gloves. Only press the spindle lock button [1-3] when the saw blade is stationary. To remove the saw blade, tilt the pendulum guard [1-8] using the handle [1-6], press the spindle lock button [1-3], and loosen the tension screw [2-2] with the hex key [2-1]. Remove the tension clamp [2-3] and the saw blade [2-4].
What safety precautions should be taken when using the saw?
Never place your hands in the cutting area or near the saw blade. Hold the device with both hands, using the auxiliary handle or motor housing. Ensure the workpiece is securely fastened to a stable surface. Avoid using damaged or incorrect blade spacers or screws. Always use the correct blade size and shape for the arbor. Be cautious of kickback and follow all safety instructions provided in the manual.
What are the noise and vibration emissions?
The noise and vibration emissions are measured according to EN 60 745. The sound pressure level is 91 dB (A), and the sound power level is 102 dB (A) with an uncertainty of 1.5 dB. The vibration emission value (ah) is 1.4 m/s² with an uncertainty of 1.5 m/s². These values are for comparison purposes and may vary depending on the application and maintenance of the tool.
How to adjust the motor electronics?
The motor electronics include soft start, which ensures a smooth start with a reduced starting current. The motor speed is adjusted automatically during idle to reduce noise and wear. Constant-Electronic maintains a nearly constant speed during idle and load, ensuring a smooth cut. An electronic overload protection stops the motor in case of extreme overload, and a temperature-dependent overload protection switches the motor to cooling mode if overheated.
How to operate the speed selector?
Use the speed selector [1-11] to adjust the speed in six steps: 2000, 2500, 3000, 3500, 4100, and 4700 min–1. The required speed depends on the saw blade and material being cut. The integrated safety overrun brake stops the saw blade within about 2 seconds after releasing the on/off switch.
How to ensure safe use of the device?
Always read and follow all safety instructions before using the device. Keep the device away from children. Ensure the workpiece is securely fastened to prevent injury. Use appropriate personal protective equipment, including hearing protection and gloves. Avoid using the device in conditions that could cause kickback or damage to the blade.
Related products from Protool
CSP 132 E
User manual 140 pages
CSP 55-2
User manual 59 pages
SBP 285
User manual 61 pages
CSP 56 EQ
User manual 66 pages
DCC-AGP 125
User manual 92 pages
CSP 165 E
User manual 96 pages
CSP 145 E
User manual 96 pages
CSP 85
User manual 100 pages
CSP 85
User manual 134 pages
CSP 68-2 EB
User manual 136 pages
RGP 150-16 E
User manual 166 pages
ISP 330 EB
User manual 182 pages