Aanmelden


of


google Doorgaan met Google

Heb je al een account?

Himiway CRUISER STEP-THRU (86 pagina's)

0 van 5
0 beoordeling

Tags

Loading...

Beschikbare talen:

Geen exacte resultaten gevonden. Pas uw zoekopdracht aan

Loading...
Heeft u hulp nodig?

Heeft u hulp nodig?

Heeft u een vraag over het product die niet in de handleiding wordt beantwoord?

  • Ontvang updates over oplossingen.
  • Ontvang antwoorden op uw vragen.

Ontvang antwoorden op uw vragen.

Afbeelding selecteren (optioneel)

Deze site wordt beschermd door reCAPTCHA. Het privacybeleid en de servicevoorwaarden van Google zijn van toepassing.

Productbeschrijving:

De Himiway CRUISER STEP-THRU is een fiets met een step-thru frame, ontworpen voor comfortabele en rustige ritjes. Het model biedt een stabiele rijervaring en is geschikt voor zowel stedelijke als buitenlandse omgevingen. De fiets is uitgerust met een solide constructie en biedt voldoende ruimte voor passagiers of bagage. Dankzij het ontwerp is het gemakkelijk om op en af te stappen, wat deze fiets ideaal maakt voor dagelijks gebruik en lange tochten.

Veelgestelde vragen

What is the recommended seat height for the Cruiser?

Adjust the seat height to a level that is appropriate for your leg length and preferred riding position. Ensure the seatpost is not extended beyond the minimum insertion mark indicated on the seatpost.

How do I adjust the seat angle?

Move the seat backward or forward and tilt it within the limit markings indicated on the seat rail. Do not exceed the limit markings to ensure safety.

What should I do before installing the pedals?

Apply a small amount of waterproof grease onto the seatpost. Ensure the pedals are installed on the correct side to avoid damaging the crank arms. Check the indicators for the right and left pedals.

How do I install the front wheel?

After tightening the rear wheel, place a piece of cardboard between the bike and the ground to protect both the bike and the ground. Carefully lift the bike up for the front wheel installation. Make sure the quick-release skewer is fully closed and check the wheel balance in the 'Pedal Only' mode.

What should I do if the front wheel is not balanced?

If the wheel is unbalanced or makes noise while rotating, it may mean the spokes were not fully tightened or not aligned horizontally. Ensure all spokes are fully tightened and properly aligned.

How do I install the headlight and front fender?

The headlight and front fender are both secured by a single bolt, so the front fender must be installed together with the headlight. If you prefer not to have a front fender, you can install the headlight by itself.

How do I install the derailleur guard?

Remove the bolts on the chainstay. Insert one bolt through the hole on the end of the derailleur hanger and use the Allen wrench to tighten it into the upper chainstay hole. Repeat on the other side.

What should I do after assembling the bike?

Ensure the seatpost is fully tightened and the seat is adjusted to your preferred height and angle. Check the wheel balance in the 'Pedal Only' mode. Make sure all bolts are tightened properly.

What should I do before using the bike?

Check all relevant requirements and regulations that apply in your country or state. There may be restrictions on riding on public roads, bike paths, or trails. There may also be requirements for helmets, age restrictions, driver's license requirements, or bike light regulations.

What should I do if I install an accessory on the bike?

Ensure the accessory is compatible and follows the manufacturer's and retailer's instructions.

Antwoord verzenden

Uw mening is belangrijk voor ons

Vindt u dat we nog iets kunnen verbeteren of toevoegen? Mist u functies of heeft u verbeteringsvoorstellen? We horen graag van u.

Beoordeling geven

5 van 5
Deze site wordt beschermd door reCAPTCHA. Het privacybeleid en de servicevoorwaarden van Google zijn van toepassing.