Nice SPIDO (78 pages)
Tags
Languages available:
No exact matches found. Please change your query
Need help?
Do you have a question about the product that is not answered in the manual?
- Receive updates on solutions
- Get answers to your question
Product description:
Frequently Asked Questions
How does the control unit detect obstacles?
The control unit detects obstacles by measuring the current absorbed by the motor during operation. This allows it to identify resistance, which is a key part of the anti-crush safety feature. The sensitivity of this detection can be adjusted during programming.
What is the purpose of the Photo-test function?
The Photo-test function is used to verify the reliability of safety devices by checking the connection between the transmitter and receiver. It ensures the system meets the UNI EN 954-1 standard (ed. 12/1998) and places the control unit and safety device in 'category 2' for safety.
How do you activate the Photo-test mode?
To activate the Photo-test mode, connect the transmitter and receiver as described in the notes on connections (Figs. 6a–6b), then press and hold the PROG button until the OK Led remains permanently on. Press the STEP-BY-STEP button to activate the mode.
What are the two operating modes of the control unit?
The control unit has two operating modes: 'Semiautomatic' and 'Automatic'. In 'Semiautomatic' mode, the system follows the 'Open – Stop – Close – Stop' sequence. In 'Automatic' mode, a programmed pause occurs after opening before the closing cycle begins.
How do you set the current sensitivity level?
Current sensitivity can be set to five levels (1 to 5), with level 3 being the default. This setting determines the motor's maximum power output. To adjust it, press and hold the PROG button until the courtesy light flashes the required number of times corresponding to the desired level.
What should you do if the OK Led doesn't light up?
If the OK Led doesn't light up, check that the power cable is correctly connected, verify that there is 24Vac between terminals 3 and 4, and ensure the fuse is working. If the fuse is blown, replace it with a 2A rapid fuse.
How do you test the control unit after installation?
After installation, power the control unit and check that the OK Led flashes at 1-second intervals. Test the safety devices, including photocells and emergency stop, and perform a full opening and closing cycle. Ensure the system responds correctly to the STEP-BY-STEP button and that the travel stops are properly positioned.
What is the maximum duration of a manoeuvre?
The maximum duration of a manoeuvre is 60 seconds. This can be programmed to range from 5 to 250 seconds depending on the system's requirements. The pause time is also programmable and affects the timing of the closing cycle after an opening manoeuvre.
What are the technical specifications of the SP6000?
The SP6000 has a power input of 230Vac ±10% at 50/60Hz, and 120Vac ±10% at 50/60Hz. It provides a 24Vac output for the flashing light and service supply, with a maximum current of 200mA. The operating temperature range is between -20°C and 70°C.
How many transmitters can be memorised in the radio receiver?
The radio receiver can memorise up to 256 transmitters. Each transmitter must be programmed individually, and all codes must be deleted if the receiver is to be reset. The SP6000 control unit uses only the first channel of the receiver, with output N°1 connected to the 'Step-by-step' function.
Related products from Nice
LFAB4000
User manual 48 pages
BFAB5024
User manual 48 pages
LFAB4024
User manual 48 pages
spido SP6000
User manual 78 pages
ME 3000
User manual 12 pages
ME 3024
User manual 12 pages
Climber CR 2024
User manual 12 pages
ROBO RO1000
User manual 76 pages
ROBO RO1000
User manual 100 pages
ROBO RO1124
User manual 100 pages
ROBO
User manual 76 pages
THOR
User manual 14 pages
THOR
User manual 16 pages
THOR
User manual 76 pages
THOR 1561
User manual 14 pages
THOR 1561
User manual 16 pages
THOR 1551
User manual 14 pages
THOR 1551
User manual 16 pages
SPIDER
User manual 16 pages
SPIDER
User manual 16 pages