Nice TEN TN2020 (228 pages)
Tags
Languages available:
No exact matches found. Please change your query
Need help?
Do you have a question about the product that is not answered in the manual?
- Receive updates on solutions
- Get answers to your question
Product description:
Frequently Asked Questions
What are the safety warnings for installing the TEN gearmotor?
Important safety warnings include: incorrect installation may cause serious injury. Always follow installation instructions carefully. Ensure the installation complies with applicable legislation and standards. Do not modify any parts unless specified. Prevent solid parts or liquids from entering the control unit. The automation cannot be used until commissioning is complete. Dispose of packaging materials according to local waste regulations. Contact NICE assistance for unresolved faults.
What are the limits of use for the TEN gearmotor?
TEN can automate up-and-over doors within specified limits. For projecting doors, max height is 2.6 m and length 3 m with one motor, or 5.4 m with two motors. For non-projecting doors, similar limits apply. The suitability depends on leaf balancing, friction, and other factors. Ensure the force required to move the door never exceeds the nominal torque specified in the technical specifications.
How do I check the product components before installation?
Check the packaging condition and ensure all components are present. Verify the presence of the gearmotor, nuts, bolts, washers, screws, and release rod. Ensure the product is in good condition and suitable for the intended installation environment.
What is the typical system configuration for the TEN gearmotor?
The typical system includes the TEN gearmotor, square tube, support bracket, telescopic arm, photocells, and a flashing light. The system is designed for up-and-over doors and includes components for safety and control. Refer to the diagram for a visual representation of the installation.
What are the wiring requirements for the TEN gearmotor?
Use cables specified in the wiring list. The power cable should be 3 x 1.5 mm² for up to 30 m, while other cables have specific types and maximum lengths. Ensure the power line is protected by a differential thermal magnetic cut-out device and has proper earthing. Use shielded cables for the aerial and ensure all connections are secure.
How do I install the gearmotor for a projecting up-and-over door?
Position the gearmotor so the axis of rotation is 50÷100 mm below the door support arm. Ensure the support bracket is perfectly vertical and aligned with the motor shaft. Use straight or curved arms depending on the space available. Secure all components and ensure the door slides freely without obstructions.
How do I adjust the limit switch for the TEN gearmotor?
The TEN 2010 uses an electronic system for absolute limit switches instead of mechanical limiters. Refer to the section on learning the door opening and closing positions for settings. Ensure the system is properly configured to detect the motor position accurately during operation.
What are the electrical connection steps for the TEN gearmotor?
Disconnect the power supply before making connections. Loosen the cover screws and route cables through the designated holes. Connect the power cable to the appropriate terminals and secure it. Use the diagram and table for cable types and lengths. Secure all cables with clips to prevent interference and ensure safety.
What are the technical specifications for the TEN gearmotor?
The technical specifications include performance data, durability estimates, and force limits. The product's durability is influenced by stress factors during operation. Use the provided tables to calculate the gravity rating and estimate the number of cycles the system can handle. Ensure the force required to move the door does not exceed the nominal torque values specified.
How do I program the direction of motor rotation for the TEN gearmotor?
Programming the direction of motor rotation is part of the Level 2 settings. Use the remote programming unit OView for this task. Ensure the motor is connected to the power supply and follow the instructions in the programming section. Verify the settings after completion to ensure correct operation.
Related products from Nice
LFAB4000
User manual 48 pages
BFAB5024
User manual 48 pages
LFAB4024
User manual 48 pages
spido SP6000
User manual 78 pages
ME 3000
User manual 12 pages
ME 3024
User manual 12 pages
Climber CR 2024
User manual 12 pages
ROBO RO1000
User manual 76 pages
ROBO RO1000
User manual 100 pages
ROBO RO1124
User manual 100 pages
ROBO
User manual 76 pages
THOR
User manual 14 pages
THOR
User manual 16 pages
THOR
User manual 76 pages
THOR 1561
User manual 14 pages
THOR 1561
User manual 16 pages
THOR 1551
User manual 14 pages
THOR 1551
User manual 16 pages
SPIDER
User manual 16 pages
SPIDER
User manual 16 pages