Adaptec 29320A (83 pages)
Tags
Languages available:
No exact matches found. Please change your query
Need help?
Do you have a question about the product that is not answered in the manual?
- Receive updates on solutions
- Get answers to your question
Product description:
Frequently Asked Questions
How many SCSI devices can the Adaptec SCSI Card 29320A support?
The Adaptec SCSI Card 29320A supports up to 15 Low Voltage Differential (LVD) and/or 15 Single-Ended (SE) SCSI devices. This allows for connecting large arrays of high-performance hard disk drives, external storage subsystems, and other SCSI peripherals.
What types of connectors does the Adaptec SCSI Card 29320A have?
The Adaptec SCSI Card 29320A includes one internal and one external 68-pin LVD connector, as well as two internal SE SCSI connectors: one 68-pin and one 50-pin. These connectors allow for connecting various types of SCSI devices.
Can the Adaptec SCSI Card 29320A work in a 32-bit PCI slot?
Yes, the Adaptec SCSI Card 29320A is a 64-bit PCI/PCI-X card but can also operate in a 32-bit PCI slot. When installed in a 32-bit slot, it automatically runs in the slower 32-bit mode.
What is the recommended way to set SCSI IDs for devices connected to the card?
Each SCSI device and the Adaptec SCSI Card 29320A must have a unique SCSI ID between 0 and 15 on each channel. The card is preset to ID 7, and the hard disk should be set to ID 0 if used as a boot device. IDs are typically set using jumpers for internal devices or switches for external devices.
How should termination be handled for SCSI devices?
Termination is essential for reliable communication on the SCSI bus. The end of each cable or the last device on the bus must have a terminator installed. Devices between the ends should have termination disabled. Ultra320/160 and Ultra2 SCSI devices require specific termination setups to function properly.
What type of cable is needed for internal Ultra320/160 or Ultra2 SCSI devices?
A special 68-pin internal LVD cable is required to connect internal Ultra320/160 or Ultra2 SCSI devices. These cables typically have twisted pairs or flat ribbon wiring and may have a built-in terminator at the end.
How do you connect internal Ultra320/160 and Ultra2 SCSI devices?
Connect the non-terminated end of the LVD cable to the internal LVD connector on the card. Attach the devices to the other end of the cable, starting with the terminated end. Ensure that the internal devices are properly terminated by the cable's built-in terminator.
How do you connect internal Wide SCSI devices?
Use a 68-pin Wide SCSI cable and connect one end to the Wide SCSI connector on the Adaptec SCSI Card 29320A. Attach the other end to a terminated Ultra/Fast Wide SCSI device. Additional devices can be connected between the two ends, but they must be unterminated.
How do you connect internal Ultra/Fast Narrow SCSI devices?
Use a 50-pin internal Ultra Narrow SCSI cable and connect it to the 50-pin internal SE Narrow SCSI connector on the card. Ensure that the devices are connected properly and that the termination is handled correctly by the cable.
What should be done before connecting SCSI devices to the Adaptec SCSI Card 29320A?
Before connecting SCSI devices, ensure that the SCSI IDs are set uniquely, termination is properly configured, and power cables are connected. Review the setup instructions for each device and consult the device's documentation for specific setup requirements.
Related products from Adaptec
AFW-1430
User manual 48 pages
2045
User manual 60 pages
51645
User manual 60 pages
52445
User manual 60 pages
5805
User manual 60 pages
5805Q
User manual 60 pages
5405
User manual 60 pages
6805
User manual 60 pages
6445
User manual 60 pages
6405E
User manual 60 pages
6405
User manual 60 pages
6405T
User manual 60 pages
6805Q
User manual 60 pages
6805E
User manual 60 pages
6805TQ
User manual 60 pages
5085
User manual 60 pages
5445
User manual 60 pages
5405Z
User manual 60 pages
5445Z
User manual 60 pages
6805T
User manual 60 pages