Dell PT1016 (80 pages)
Tags
Languages available:
No exact matches found. Please change your query
Need help?
Do you have a question about the product that is not answered in the manual?
- Receive updates on solutions
- Get answers to your question
Product description:
Frequently Asked Questions
How do I install the pass-through module?
To install the pass-through module, first remove the pin cover from the connector pins at the back of the module. Locate an empty module bay in the server, and ensure the latching arm is in the unlatched position. Slide the module into the bay until it stops, then rotate the latching arm upward until it is flush against the front panel and seated in the latch.
What type of fiber optic cable should I use?
Use multimode fiber optic cable with short-wave lasers that meets the following specifications: 62.5/125 µm with a bandwidth of 200 MHz*km. The maximum length depends on the data rate: 300 meters at 1.0625 Gb/s, 150 meters at 2.125 Gb, and 70 meters at 4.25 Gb/s. The minimum length is 0.5 meters.
What are the static precautions during installation?
Computer equipment contains static-sensitive components that may be damaged during handling. It is recommended to use static precautions such as grounded wrist straps during the installation process to prevent damage to sensitive components.
How do I remove a blank I/O module from the server?
If the selected module bay contains a blank I/O module, you should remove it before installing the pass-through module. This ensures the bay is empty and ready for the new module.
What is the purpose of the latching arm?
The latching arm is used to secure the pass-through module in the server bay. It must be rotated upward until it is flush against the front panel and seated in the latch to ensure the module is properly installed and locked in place.
What should I do if the module does not latch properly?
If the module does not latch properly, check that the latching arm is fully rotated upward and seated in the latch. Ensure the module is fully inserted into the bay until it stops. If the issue persists, recheck the installation steps or consult the user manual for further guidance.
Can I use a different type of fiber optic cable?
It is recommended to use multimode fiber optic cable with short-wave lasers that adhere to the specified bandwidth and length requirements. Using a different type of cable may affect performance or compatibility with the target device.
What is the minimum length of the fiber optic cable?
The minimum length of the fiber optic cable is 0.5 meters. This ensures proper signal transmission while avoiding unnecessary signal loss or degradation.
What should I do if the module is not seated correctly?
If the module is not seated correctly, ensure that it is fully inserted into the bay until it stops. Check that the latching arm is properly rotated and seated in the latch. If the issue persists, recheck the installation steps or consult the user manual for further assistance.
What are the specifications for the fiber optic cable?
The fiber optic cable must be multimode with a core size of 62.5/125 µm and a bandwidth of 200 MHz*km. The maximum length varies depending on the data rate: 300 meters at 1.0625 Gb/s, 150 meters at 2.125 Gb/s, and 70 meters at 4.25 Gb/s. The minimum length is 0.5 meters.
Related products from Dell
emulex PT1016
User manual 80 pages
M8428-k
User manual 172 pages
M8428-k
User manual 202 pages
PowerConnect 3548
User manual 266 pages
PowerConnect 3524P
User manual 266 pages
PowerConnect 3548P
User manual 266 pages
Networking N1500 Serie
User manual 268 pages
PowerConnect PC6248
User manual 282 pages
PowerConnect PC6224F
User manual 282 pages
PowerConnect PC6224
User manual 282 pages
PowerConnect PC6248P
User manual 282 pages
PowerConnect PC6224P
User manual 282 pages
Networking S5000
User manual 346 pages