SICK W26 (149 pages)
Languages available:
No exact matches found. Please change your query
Need help?
Do you have a question about the product that is not answered in the manual?
- Receive updates on solutions
- Get answers to your question
Product description:
Frequently Asked Questions
How to adjust the switching distance?
To adjust the switching distance, press the teach-in button for approximately 1-3 seconds to set the distance. For fine-tuning, use the potentiometer without pressing the teach-in button. Turning the potentiometer to the right increases the switching distance, while turning it to the left decreases it. The switching distance can also be adjusted solely using the potentiometer.
What are the operating conditions for the sensor?
The sensor requires a background as a reference. The background should remain as consistent as possible in terms of reflectivity and position. The maximum distance between the sensor and the background, as well as the minimum object height, must be observed. Use the corresponding diagram to align the distance (switching distance) and minimum object height (y) with the reflectivity of the background and object.
How to check the sensor's functionality?
To check the sensor's functionality, use the test input (TE) to turn off the transmitter and verify the sensor's operation. Ensure no object is between the sensor and the background. Refer to Table 5 for test conditions. If the switching output does not match the diagram, check the operating conditions and refer to the troubleshooting section.
What is the purpose of the test input?
The test input (TE) allows the sensor to be turned off, enabling verification of its proper function. When using a junction box with LED indicators, ensure the TE is correctly connected. Activating the test input simulates an object detection and can be used to test the sensor's response.
What are the electrical installation requirements?
The sensor must be connected with the power supply disconnected. Follow the pin configuration and wire color codes depending on the connection type. Ensure all electrical connections are made before applying power. The alarm, health, and other outputs are defined in the connection schema, with specific pin configurations for different connection types.
How to mount the sensor?
Mount the sensor on a suitable mounting angle as specified in the SICK accessory program. Ensure the maximum allowable torque of the sensor is less than 1.3 Nm. Position the object so that it faces the sensor, as shown in the diagram on page 16.
What are the technical specifications?
The sensor operates on a DC voltage range of 10 to 30 V. The wiring and pin configuration vary depending on the connection type (push-pull, PNP, or NPN). The switching distance and time functions can be adjusted using the potentiometer and teach-in button. The sensor is suitable for detecting flat, shiny, and uneven objects.
How to align the sensor?
For the WTF26P model, align the sensor with the background so that the red light beam hits the object. Ensure the optical aperture (front lens) is completely clear. For the WTF26I model, align the sensor with the background so that the infrared light (not visible) hits the object. The correct alignment can only be detected using the LED indicators, as shown in the diagram.
What are the safety precautions?
Read the operating manual before using the device. Only trained personnel should handle the installation, mounting, and configuration. Avoid exposing the sensor to direct UV radiation or weather influences unless specified in the manual. Protect the device from moisture and contamination during operation.
What is the UL certification requirement?
The device must be supplied from an isolating transformer with a secondary overcurrent protective device that complies with UL 248. The transformer should be rated for either a maximum of 5 amps for voltages 0 to 20 V (0 to 28.3 V peak), or 100/Vp for voltages 20 to 30 V (28.3 to 42.4 V peak). Alternatively, the device can be supplied from a Class 2 power supply.
Related products from SICK
W9-3
User manual 54 pages
W9-3
User manual 144 pages
LFP Inox
User manual 56 pages
WLA12L
User manual 212 pages
WE34
User manual 164 pages
WS34
User manual 131 pages
WS34
User manual 164 pages
WTF12L
User manual 232 pages
WTF12V
User manual 232 pages
WL34
User manual 164 pages
WT34
User manual 133 pages
GL6L
User manual 117 pages
GTB6L
User manual 160 pages
GTE6L
User manual 109 pages
GTE6L
User manual 130 pages
GTE6L
User manual 160 pages
GSE6L
User manual 119 pages
M4000 Standard
User manual 92 pages
LFH
User manual 48 pages
1049051
User manual 54 pages